Here is my little DIY on how you can make this same wine rack.
You will need the following cuts (And there are lots & lots of cuts!):
Qty 112 = 1″x1″x12″ (Bottle separators)
Qty 28 = 1″x3″x12″ (Sides of the wine rack shelf)
Qty 28 = 1″x2″x32″ (Front & back of the wine rack shelf)
For the main support for the shelves you will need:
Qty 4- 1″x3″x84″
Shims to level out the wine rack
Before you start this project please make a note that I drilled holes before placing all screws. I didn’t want any of the wood to split, so drilling holes will prevent that. Every time you read “screw them together” it really means “drill a hole for the screw and then screw them together.”
To start the rack, build the frame of the shelves. Take two 1″x3″x12″ boards and screw them to two 1″x2″x32″ boards.
You should end up with a rectangle frame like below. (Note: There are two screws in each corner. Each shelf should have 8 screws in it for stability.) Now repeat this step 13 more times!
You will end up with 14 shelves that look like this:
Next are the bottle separators. There are 112 of them so be ready! There are two options with the wine bottle separators:
Option 1- Uniform Shelves
If you would like to have your wine rack be uniform and the shelves to hold the exact same size/amount of bottles, you will need to space the bottle separators 3 inches apart. (You will only get 98 bottle spaces this way.)
Option 2- Varying Shelves
I decided that I wanted this wine rack to hold our skinny bottles (which we have bottle mead in) and also the larger 1.5 bottles. I took my top two racks and place the separators 2 inches apart. This allowed me the two racks to hold 18 skinny bottles. On the bottom two racks, I place the separators 3.5 inches apart, allowing me to hold 12 of the larger 1.5 liter bottles. Leaving 10 racks, with separators 3 inches apart, to hold 7 bottle each. (You will be able to hold 100 bottles this way.)
The choice is up to you, but my examples below show what I did on the majority of my wine racks, which means 3 inches apart, having each shelf hold 7 bottles of wine.
Start out by screwing the first wine separator to the shelf frame. The separator should start on the inside of the 1″x3″x12″ board.
Now to make this step go faster, I cut a 3 inch board to be a spacer between my separators.
I also made a stick that went the width of the shelf showing where each separator should be placed.
Eventually you will have each of the separators installed and ready to go.
I worked very hard on putting these rack together and it became an evening project to watch tv, drink a glass of wine, and assemble a few racks each night. Doesn’t that sound wonderful? Have a glass of wine while building a wine rack? Well, it sounds great until that point where you accidentally drop your drill on your thumb!
So kids, the lesson we learned is power tools and alcohol do not mix! By the way, I smashed my thumb almost two months ago and the picture above is what it looks like now. I would have showed you the before, but it was a pretty bloody mess so I thought I would spare you. Maybe by summer the bruise will grow out!
Other than the injury, I finally finished all 14 shelves.
After all the shelves were completed, I decided to stain them all a dark cherry that pretty matches all my other furniture in the house.
Now comes the difficult part, assembling the wine rack. You will most likely require a helper, and my husband was so kind to help me out. We laid the wine rack on it’s side and placed the 1″x3″x72″ boards on the backside of the racks. (Take note, we started with the back first incase we made any errors while screwing it together.) We decided each rack needed to be 6 inches apart and began screwing the racks in place.
The screws should run through the 1″x3″x72″ board into the bottom of the shelf (the 1″x3″x12″ board.) Once all are attached on the back, flip it over and start with the front. It is very important when you are assembling the rack that you make sure all shelves are attached level both front and back and side to side. This will prevent any bottles from falling off the rack.
We decided to put the rack up in our utility room, out of the way of a certain little boy that might want to try climbing it. Wherever you decided to place the rack, your floor might not be level so use shims to level out the rack. Again, this will to prevent bottles from falling off the rack and the wine rack from falling over. In addition to the shims, we also screwed the rack to the wall to prevent it from falling over. I am pretty sure 100 bottles of wine would REALLY hurt if it fell on someone!
The rack is finished and we LOVE it! Though we haven’t quite filled it up, we love the extra wine storage it provides. (If you are wondering how we acquired so many bottles, we make our own wine.)
Some of the shelves are holding empty bottles, but hopefully we get a new batch of wine brewing soon so we can replace them with full bottles.
I hope this DIY project inspired some of you new to woodworking to get out there and try it for yourself. Like I say a lot in this blog– If I can do it, you can do it! Happy building!